To keep band T-shirt prints from fading, turn the shirt inside out before washing it in cold water on a gentle cycle, away from the sun. On a US care label, "cold" means water that starts at up to 86°F (30°C). Heat, agitation and sunlight are what wear a graphic down, and contribute to wear and fading.
These steps apply to both a well-worn tour shirt and a new rock and roll band T-shirt. Start by checking the garment's care label, then follow the tips below.
Why Do Band Tee Prints Fade and Crack?
Band tee prints fade and crack mostly from heat, agitation and sunlight. Polyprint, a company that makes DTG printers, says high wash temperatures and high-speed cycles can fade a print's colors and crack or peel the ink. sh temperatures and high spin speeds can cause printed colors to fade and ink to crack or peel. On dark shirts, tumbling can also rough up the fabric fibers, creating a fuzzy surface that makes the shirt look faded, as Consumer Reports explains.
Sunlight can also fade printed colors over time. Polyprint recommends keeping DTG-printed garments away from prolonged sun exposure. Consumer Reports also recommends drying dark clothes indoors rather than outdoors.
What Do the Care Label Instructions on Your Band Tee Mean?
Under the FTC's Care Labeling Rule, the words on a US care label have set meanings. Understanding them helps you know how much heat and agitation your shirt can handle.
"Cold" means the initial water temperature should not exceed 86°F (30°C). A label that says only "Machine wash," with no temperature, means the garment can be regularly washed in hot water up to 145°F (63°C).
"Wash inside out" means turning the shirt inside out to protect the face of the fabric, where the graphic is printed. "Gentle" or "delicate" cycle means slow agitation and a shorter wash.
Drying terms work in much the same way. "Tumble dry" with no heat setting means a hot dryer setting may be used regularly. "Line dry in shade" means hanging the shirt to dry away from direct sunlight.
Warnings are just as important. The rule requires care labels to warn against methods that could harm the garment, such as ironing. For example, "Do not iron" means ironing could damage the shirt. "Only non-chlorine bleach, when needed" means regular chlorine bleach should not be used. Manufacturers must also have a reasonable basis for their care instructions. If a general tip in this guide conflicts with your shirt's label, follow the label.
How to Wash a Band T-Shirt Without Fading the Print
A few simple changes to your washing routine can help protect a band tee's print from fading, cracking, or peeling. Follow these steps before putting your shirt in the wash.
Read the label. Look for a temperature, a cycle and any "Do not" warning before the shirt goes in.
Turn it inside out. Consumer Reports recommends this for dark clothes because agitation breaks down the outer fibers. Polyprint gives the same advice for DTG prints.
Wash cold. Set the machine to cold, which on a US label means up to 86°F.
Use the gentle cycle. Pick the shortest cycle that still gets the shirt clean. Consumer Reports notes that less time in the washer means less fading on dark clothes.
Use liquid detergent and leave room in the drum. For DTG prints, Polyprint advises liquid detergent over powder and warns against overloading the washer.
Skip fabric softener and check the bleach line. Polyprint says softener can make DTG prints peel. If the label reads "Only non-chlorine bleach, when needed," use non-chlorine bleach and only when the shirt needs it.
How Should You Dry and Iron a Band Tee?
Air drying is a good way to protect a band tee's print. After washing, hang the shirt indoors and let it dry naturally. Avoid putting it in the dryer, as repeated tumbling and heat can contribute to fading and wear.
If you prefer to dry your shirt outside, turn it inside out so the print is not directly exposed to sunlight. UV exposure can cause print colors to fade over time.
Ironing comes down to the label. If the tag says "Do not iron," the maker is warning you that ironing would harm the shirt, so skip it.
Does the Print Type Change Anything?
It can. The DTG advice above comes from a DTG printer maker, so it fits shirts printed that way. Metal Babe Mayhem's Ms. Vampy tees are one example: each one is printed to order on a direct-to-garment printer.
All-over-print pieces are a different case. The Dark Lips all-over-print tank is sublimation printed on 82% polyester and 18% spandex, a four-way stretch fabric, so follow the care its own label lists.
[CLIENT NOTE: Which print method do you use on your core tees, tanks and hoodies (screen print, DTG, DTF)? The site states DTG only for Ms. Vampy and sublimation for the all-over-print tanks.]
How Often Should You Wash a Band Tee?
Wash your band tee when it needs it, rather than after every wear. Consumer Reports notes that the more you wash dark clothes, the more dye washes out, and suggests airing them out between washings instead. If your black band tee isn't sweaty or stained after a show, air it out overnight and wear it again.
Tonight, pull your favorite band tee out of the drawer and read its label before the next load. Then try it in a new outfit with these ideas for styling rock tees, or browse the women's rock tees at Metal Babe Mayhem when you're ready for another one.
